Kitchen faucet hook up

kitchen faucet hook up

How do you hook up a kitchen faucet?

Hooking up the hot and cold water is often the final step when installing a kitchen faucet. Typical plumbing for a kitchen sink includes a drain line and a pair of water lines with shutoff valves under the sink. In most cases, the hot water is on the left and the cold water is on the right.

How do you install a pull down kitchen sink faucet?

Install washers and nuts underneath the sink. If you used caulk or plumbers putty for the gasket/trim ring installation, wipe away excess underneath the sink. For pull-down faucets, attach the quick-connect hose to the supply pipe. Pull down on the hose and attach the weight. The weight needs clearance to hang freely underneath the sink.

Do you Mount the faucet to the sink or cabinet?

Premount the Faucet on New Sink Installations If youre installing a new sink along with your faucet, mount the faucet to the sink before you install the sink. Its much simpler than lying on your back inside the sink cabinet to install the faucet.

Where can I get a supply line for a kitchen faucet?

Supply lines with integral washers are available at most home centers. Obtain the lines based on the distance from the valves to the underside of the faucet. Open the cabinet doors below the sink. Look to the rear of the sink and locate the threaded stems on the underside of the faucets where the supply lines attach.

How do you install a new kitchen faucet?

Now that youve removed the old faucet, its time to install the new one. Because all faucets are different, refer to the manufacturers installation instructions. Place the rubber or plastic gasket, or trim ring, over the faucet holes in the sink and set the deck plate.

How do you attach a quick connect hose to a faucet?

For pull-down faucets, attach the quick-connect hose to the supply pipe. Pull down on the hose and attach the weight. The weight needs clearance to hang freely underneath the sink.

How to install a pull down kitchen faucet?

Install the New Kitchen Faucet 1 Set the Deck Plate. Place the rubber or plastic gasket, or trim ring, over the faucet holes in the sink and set the deck plate. 2 Feed in the Lines 3 Affix the Hardware Under the Sink 4 Set Up the Pull-Down Faucet 5 Connect the Lines 6 Check for Leaks 7 Clear the Lines 8 Replace the Aerator

How do you attach a sprayer to a kitchen faucet?

Set the sprayer base in one of the holes in your sink and screw on the mounting nut to secure it in place. Feed the sprayer hose through the base and attach the end of the hose to the bottom port on your faucet.

How to install a new kitchen faucet?

Take the hot and cold supply lines and put them on your new faucet directly. These supply lines have a diverter that can connect an extended supply line. Place a faucet gasket into the spout base and cover it over the supply lines. Make sure all the components fit properly. Now, place the faucet on the mounting surface.

Where do the supply lines go on a faucet?

Factory-attached tubes: Some faucets come with factory-attached soft-copper supply lines on both the hot- and cold-water tailpieces, which means the only attaching will be directly to the shut-off valves. You should, however, do a little preshaping of the soft-copper before setting the sink into position in the countertop.

What size water line do I need for a faucet?

Water supply lines come in 3/8 sizes as a standard. You can find them easily in 12-inch lengths, which should be long enough for your project. Youll also need 3/8 compression couplings to join the water lines to your existing plumbing and to the plumbing on the faucet.

What is a faucet line adapter?

The faucet supply line adapter is a small threaded metal bit. While both these parts technically extend your water line from one spot to another, the extension is the one with the hose or hoses. You can get both single and double extenders, but it’s common to find two because there are hot and cold-water lines.

Related posts: